BGS

• knurled
• sockets, Spline (for RIBE),
  12.5 mm (1/2") drive: M6S, M8S, M12S  
• special sizes suitable for:
  Nissan, Renault, for couplings, cylinder heads etc.

Technical data:

scope of delivery:

• 8 conical centering bushes for clutch discs with hole sizes: 14.5 - 25.5 mm
• 8 adaptors for centering in the crankshaft: 10.8 - 12.2 - 13.5 - 14.7 - 15.8 - 17.1 - 18.3 - 19.9 mm
• centering shaft 145 mm

Technical data:

• for clutch discs with 15 to 28 mm clutch hub diameter
• allows an accurate centering of the clutch disc on vehicles with or without pilot bearing
• alignment according to friction surface of the clutch pressure plate
• suitable for most vehicles
• centering sleeve Ø: 12, 14, 15, 16, 17, 18 & 19 mm

Technical data:

• universal use for vehicles with a hub diameter of Ø 15.0 mm - 26.6 mm
• for mounting single-disc dry clutches
• centering the clutch disc over the guide bearing is not necessary
• in 2 sizes: 15 - 19 mm and 20 - 26.6 mm

Technical data:

• ideally suited for disassembly and assembly of balancer shafts and crank shaft flanges
• all-purpose, incl. 9 adaptors

scope of delivery:

• 1 puller plate, 20 mm holder
• 12 screws, 3 pcs each: 3/8"NC16 x 57 mm - 3/8"NC24 x 57 mm - M6 x 1.0 x 60 mm - M8 x 1.25 x 60 mm
• 1 centre bolt 10 mm
• 9 adaptors:
  • M12 x 1.5 - 3/8"NC16
  • M14 x 1.5 - 3/8"NC16
  • M16 x 2.0 - 3/8"NC16
  • 1/2" x NC20 - 3/8"NC16
  • 9/16" x NC18 - 3/8"NC16
  • 7/16" x NC20 - 3/8"NC16
  • 3/4" x NC16 - 3/8"NC16
  • 5/8" x NC18 - 3/8"NC16
  • 3/8" x NC16 - 3/8"NC16

Technical data:

• crankshaft locking tool to be used as OEM T10340

suitable for the following vehicles/engines:

• Audi A3 (manufactured between 2003 and 2010)
• Seat Ibiza, Leon, Altea
• Skoda Octavia (manufactured between 2004 and 2009), Fabia (manufactured between 2007 and 2009), Superb (manufactured between 2009 and 2010), Roomster (manufactured between 2006 and 2009)
• VW Golf (manufactured between 2003 and 2009), Golf Plus (manufactured between 2005 and 2009), Jetta (manufactured between 2006 and 2009), Passat (manufactured between 2005 and 2009), Polo (manufactured between 2002 and 2008), Scirocco (manufactured between 2009 and 2010), Tiguan (manufactured between 2007 and 2009), Touran (manufactured between 2003 and 2009), Eos (manufactured between 2006 and 2009)
• engine code AXU, BLG, BAG, BMY, BKG, BMK, BLF, CAVA, BLN, CAVB, BLP, CAVC, CAVE, CAVF, CAVD, CAXA, CAXC, CDGA, BTS

Technical data:

• suitable for Ford Transit 2.2 manufactured as of 2006
• for locking crankshaft and flywheel
• allows the TDC sensor position to be set after working on cam chain drive system
• crankshaft locking tool to be used as OEM 303-1587
• flywheel locking tool to be used as OEM 21-251 / 303-698
• timing pump locking pin to be used as OEM 0188H / 1860965000

Technical data:

• for holding the crankshaft pulley while loosening or tightening the middle pulley bolt
• allows safe and damage-free removal / installation
• to be used as OEM 116480

Technical data:

• suitable for Peugeot 206 / 306 / Expert / Partner / Xsara / Berlingo / Dispatch Motor 1.9D, 1.9 HDI
• engine code WJY(DW86), WJZ(DW8)
• spare part is marked in Figure with number 30

Technical data:

• spare part is marked in Figure with number 2

Technical data:

• crankshaft locking tool with aligning pin
• to be used as OEM T10226
• suitable for e. g. VW Tourag, Phaeton

Technical data:

suitable for the following models:

• VAG 1.2 - 1.4 - 1.9l TDI engines with round crankshaft wheel
  
  
• to be used as OEM T10050

Technical data:

• suitable for VW 1.4 / 1.6 / 2.0 l engines (engine codes ADX, AEA, AEE, AEH, AEX, AFH, AFK, AGP,AGR, AHW, AJM, AKL, ALN, AMF, ANA, ANY, APE, APF,ARM, ATJ, AUA, AWH)
• for counterholding the belt pulley of 4-valve engines with pin diameter 11.5 mm
• also for counterholding the belt pulley of 2-valve engines

suitable for the following models:

• VW: Beetle, Bora, Caddy, Golf, Lupo, Polo, Sharan, Touran, Transporter
• Audi: A2 / A3 / A4 / A6, TT
• Skoda: Fabia, Octavia, Superb

Technical data:

• measures the coating thickness on iron-metal and non-iron-metal (steel, copper, aluminum, brass, etc.)
• digital display with backlight
• one-hand operation
• measuring range: 0 - 40 mils / 0 - 1000 µm
• resolution: 0.1 mils / 0.1 µm
• accuracy: +/- 4 dgts (0 - 7,8 mils) +/- 10 dgts (0 - 199 µm)
• response time: 1 sec
• auto hold function
• automatic power off
• delivered with bag
• including battery, calibration pad & manual

Technical data:

• measures the coating thickness on iron-metal
• digital display with backlight
• one-hand operation
• measuring range: 0 - 40 mils / 0 - 1000 µm
• resolution: 0.1 mils / 0.1 µm
• accuracy: +/- 4 dgts (0 - 7,8 mils) +/- 7 dgts (0 - 199 µm)
• response time: 1 sec
• auto hold function
• automatic power off
• delivered with bag, battery, calibration pad & manual

Technical data:

• comprehensive kit for fast and effective removal and installation of wheel bearings & suspension bushes
• reduces the possibility of damaging the bearing and housings
• plates and sleeves can also be used in a common workshop press

scope of delivery:

• supplied with 4 stepped end plates
• pressure plates: Ø 83 x 20 mm
• 4 screws: M10 x 1.5 - M12 x 1.5 - M14 x 1.5 M16 x 1.5 mm, 450 mm long
• pressure sleeves with outer-Ø 44, 46, 48, 50, 52, 54, 56, 58, 60, 62, 64, 66, 68, 70, 72, 74, 76, 78, 80, 82 mm
• sleeve wall thickness: 5 mm
• sleeve height: 94 mm

Technical data:

• suitable for BGS 67301

Technical data:

• for non-damage mounting of bearings and sealing rings
• suitable for most bearings

scope of delivery:

• 33 nylon and 3 metal mounting sleeves
• pressure piece sizes: 10 - 26 mm / 10 - 30 mm / 10 - 35 mm / 12 - 28 mm / 12 - 32 mm / 12 - 37 mm / 15 - 32 mm / 15 - 35 mm / 15 - 42 mm / 17 - 35 mm / 17 - 40 mm / 17 - 47 mm / 20 - 42 mm / 20 - 47 mm / 20 - 52 mm / 25 - 47 mm / 25 - 52 mm / 25 - 62 mm / 30 - 55 mm / 30 - 62 mm / 30 - 72 mm / 35 - 62 mm / 35 - 72 mm / 35 - 82 mm / 40 - 68 mm / 40 - 80 mm / 40 - 90 mm / 45 - 75 mm / 45 - 85 mm / 50 - 80 mm / 50 - 90 mm
• pressure disk sizes 45 - 100 mm / 50 - 110 mm

Technical data:

• made from aluminium

scope of delivery:

• 3 drift pins: Ø 11 - 16 - 21 mm
• 13 pressure pieces:
  • 10 mm internal diameter x 12 mm external diameter
  • 12 mm internal diameter x 14 mm external diameter
  • 14 mm internal diameter x 16 mm external diameter
  • 15 mm internal diameter x 17 mm external diameter
  • 16 mm internal diameter x 18 mm external diameter
  • 18 mm internal diameter x 20 mm external diameter
  • 19 mm internal diameter x 21 mm external diameter
  • 20 mm internal diameter x 22 mm external diameter
  • 22 mm internal diameter x 24 mm external diameter
  • 25 mm internal diameter x 27 mm external diameter
  • 26 mm internal diameter x 28 mm external diameter
  • 28 mm internal diameter x 30 mm external diameter
  • 30 mm internal diameter x 32 mm external diameter

Technical data:

• slotted, swivel head with hexagon and double hexagon drive

Technical data:

• similar to Oxygen Sensor Socket Set BGS 1140

Technical data:

• for loosening of oxygen sensors
• suitable for e. g. air hammer BGS 3515
• 10 mm shank diameter
• suitable for oxygen sensors with hexagonal profile, 22 mm

Technical data:

scope of delivery:

• oxygen sensor socket, 12,5 mm (1/2") drive, 30 mm, 12-point, length 80 mm: for Bosch, General motors, Mercedes-Benz
• oxygen sensor socket, 12,5 mm (1/2") drive, 27 mm, hexagon, length 80 mm: for all types of cars
• oxygen sensor socket, 12,5 mm (1/2") drive, 28 mm, 12-point, length 80 mm: for Volvo, Scania, HGV
• oxygen sensor socket, 12,5 mm (1/2") drive, 21 mm, 12-point, length 85 mm: for Ford, VAG
• oxygen sensor socket, 12,5 mm (1/2") drive, 27 mm, 12-point, length 85 mm: for BMW, Fiat, Ford, Peugeot
• oxygen sensor socket, 12,5 mm (1/2") drive, 22 mm, 12-point, length 80 mm: for all types of cars
• oxygen sensor socket, 12,5 mm (1/2") drive, 27 mm, 12-point, length 110 mm: for PSA
• oxygen sensor socket, 12,5 mm (1/2") drive, 22 mm, 12-point, length 110 mm: for Audi, BMW, Mercedes-Benz, VW, Volvo
• oxygen sensor socket, 12,5 mm (1/2") drive, 22 mm, 12-point, length 150 mm: for BMW
• oxygen sensor socket, 12,5 mm (1/2") drive, 20 mm, hexagon, length 80 mm, slotted: for all types of cars
• oxygen sensor socket, 12,5 mm (1/2") drive, 19 mm, 12-point, length 80 mm: for VW, Audi, Seat
• oxygen sensor socket, 12,5 mm (1/2") drive, 17 mm, 12-point, length 80 mm: for BMW, Mercedes-Benz, Renault
• oxygen sensor socket, 12,5 mm (1/2") drive, 22 mm, 12-point, length 50 mm, offset drive: for all types of cars
• oxygen sensor socket, 10 mm (3/8") drive, 22 mm, hexagon, length 30 mm, offset drive: for all types of cars

Technical data:

• for assembly of oxygen sensors, radiator thermo switches and diesel injection nozzles

scope of delivery:

• 29 x 90 mm, 12,5 mm (1/2") drive, slot 7 mm
• 22 x 90 mm, 10 mm (3/8") drive, slot 20 mm
• 22 x 74 mm, 10 mm (3/8") drive
• 27 x 78 mm 12-point, 12,5 mm (1/2") drive, window 28 mm
• 22 x 80 mm, 10 mm (3/8") drive, slot 9 mm
• 22 mm offset, 10 mm (3/8") drive, slot 8 mm
• 22 mm offset, 12,5 mm (1/2") double-4-point drive, slot 11 mm

Technical data:

• forged
• tempered jaws

Technical data:

• forged
• tempered jaws

Technical data:

Technical data:

Technical data: